X Server Messages

EXECD Messages

EXECD messages pertain to the execution of local clients. If you are looking for a message that refers to the EXECD module but does not appear here, refer to "Messages Common to All Modules".

BADCMD, invalid command: command

Severity:: Error

Explanation:: The EXEC daemon does not recognize the specified command, usually a local client command.

User Action:: Check the System Administrator's Guide for UNIX Systems or the client man page to determine the correct command for the desired local client.

BADERRPORT, invalid error port number in request

Severity:: Error

Explanation:: The X server has detected an internal error.

User Action:: If you encounter this message, please contact NCD Technical Support.

BADLICENSE, terminal not licensed for: feature

Severity:: Error

Explanation:: The terminal does not have a license for the specified feature, such as DPS.

User Action:: Contact NCD to obtain a valid license for the desired feature and enter it in the terminal's remote configuration file, NVRAM, or license.dat file.

BADMODDIR, bad modules directory: dir

Severity:: Error

Explanation:: The X server was unable to load modules from the configured directory.

User Action:: Make sure that the modules are in the correct location and accessible.

BADPARAMS, invalid parameters given for: client

Severity:: Error

Explanation:: The specified local client does not recognize the command-line options it received through the EXEC daemon.

User Action:: Verify that the command-line options are correct for the specified client.

BADPORT, refused request from nnn.nnn.nnn.nnn on bad port n

Severity:: Error

Explanation:: The EXEC daemon has received a request for connection from the specified host. The EXEC daemon is refusing the request because the request did not originate from a privileged TCP port on the host. Specifically, the requesting TCP port number is equal to or greater than 1024.

User Action:: Verify the host system is using the correct TCP port.

DISABLEDCMD, command has been disabled:command

Severity:: Error

Explanation:: Command cannot be executed because it has been configured as disabled.

User Action:: Remove command from the exec-disabled-commands remote configuration parameter.

LOADCMD, error loading command:command

Severity:: Error

Explanation:: The X server is unable to load a module needed to run the command.

User Action:: Make sure that the modules are present and in the correct location.

LOADDISABLED, loading of module module has been disabled

Severity:: Error

Explanation:: The module has been configured to be disabled.

User Action:: Change the load policy for the module in the modules-load- policy remote configuration parameter.

LONGCMD, command string too long

Severity:: Error

Explanation:: The command that has been entered exceeds the limit of 512 characters.

User Action:: Re-enter the command, limiting the entry to 512 characters.

LONGUSER, user name too long

Severity:: Error

Explanation:: The user name that has been entered is too long.

User Action:: Re-enter the user name, limiting the entry to 16 characters.

NOERRCONN, unable to connect to error socket: message

Severity:: Error

Explanation:: The network connection has failed.

User Action:: Verify that the host is operational, that it is communicating on the network, and that the network is working.

NOERRPORT, unable to read port number from request

Severity:: Error

Explanation:: The X server has detected an internal error.

User Action:: If you encounter this message, please contact NCD Technical Support.

NONIPERRPORT, error port given on non-IP connection

Severity:: Error

Explanation:: The X server has specified a port number when communicating across a DECnet network.

User Action:: If you encounter this message, please contact NCD Technical Support.

NORESPORT, no reserved ports available

Severity:: Error

Explanation:: The X server has detected an internal error.

User Action:: If you encounter this message, please contact NCD Technical Support.

OPENMODFAIL, unable to open module module

Severity:: Error

Explanation:: The X server cannot find module.

User Action:: Make sure that the module is in the modules directory.

PROCLIM, too many copies already running: client

Severity:: Error

Explanation:: The user has requested a local client when the maximum number of the client's processes already exist.

User Action:: Use an existing client process, or close one of the existing client processes and open a new one.

START, running command: command

Severity:: Information

Explanation:: The EXECD module has started the specified command as requested.

User Action:: None

UNKNOWNERR, unknown error for: client

Severity:: Error

Explanation:: The specified local client has failed with an unknown error code.

User Action:: If you encounter this message, please contact NCD Technical Support.

[Top] [Prev] [Next] [Contents] [Index]

Send comments, suggestions, or questions about this document to the NCD Technical Publications Department by Internet e-mail. Write to us at techpubs@ncd.com.